| Widow Spydey in CZ (designed by Greg Glenn) cut by Tyler Miller on the GemMaster II. |
GemMaster II
THE ULTIMATE IN PRECISION AND ACCURACY
The secret of accuracy of the GemMaster II is found not only in its high quality components, electronic circuitry and craftsmanship, but also in its unparalleled "standard" features. These features are designed to
make the GemMaster II the easiest and most accurate faceting machine available, while slashing the amount of time required. First and foremost is the ELECTRONIC MICRO STOP (EMS) METER, THE
HEART OF THE GemMaster II.
HERE IS HOW THE EMS CAN IMPROVE YOUR ACCURACY AND SAVE YOU TIME:
As the first facet in a series is cut to the desired angle and depth, the needle moves up the meter scale. When the facet is completed and the grinding stops, the position of the needle on the meter is noted. As each
subsequent facet in a series is cut, an audible tone denotes the identical needle position on the meter. Upon hearing this tone, you know to move on to the next facet. When using this method, upon completion
not only are all your facets identical but your time involved is cut dramatically! If the use of the tone is not desired, a switch is provided to turn it off and allow only the meter needle to operate.
Example: After the first facet in a series is cut (taking a minimum of time) the remaining facets in the series can be cut in six to ten seconds each!
STANDARD FEATURES OF THE GemMaster II:
MACHINE SPECIFICATIONS
THE ULTIMATE IN PRECISION AND ACCURACY
The secret of accuracy of the GemMaster II is found not only in its high quality components, electronic circuitry and craftsmanship, but also in its unparalleled "standard" features. These features are designed to
make the GemMaster II the easiest and most accurate faceting machine available, while slashing the amount of time required. First and foremost is the ELECTRONIC MICRO STOP (EMS) METER, THE
HEART OF THE GemMaster II.
HERE IS HOW THE EMS CAN IMPROVE YOUR ACCURACY AND SAVE YOU TIME:
As the first facet in a series is cut to the desired angle and depth, the needle moves up the meter scale. When the facet is completed and the grinding stops, the position of the needle on the meter is noted. As each
subsequent facet in a series is cut, an audible tone denotes the identical needle position on the meter. Upon hearing this tone, you know to move on to the next facet. When using this method, upon completion
not only are all your facets identical but your time involved is cut dramatically! If the use of the tone is not desired, a switch is provided to turn it off and allow only the meter needle to operate.
Example: After the first facet in a series is cut (taking a minimum of time) the remaining facets in the series can be cut in six to ten seconds each!
STANDARD FEATURES OF THE GemMaster II:
- Keyed dops for an easy and more accurate transfer.
- Large brass platen results in greater stability for the lap.
- Lap direction is reversible.
- Renewable thread in lap spindle to compensate for thread wear.
- Mast on left or right.
- Larger stainless steel water container with water-level sight-gauge.
- Available in 110 or 220 volts.
- 1 Color Coded #96 Index Plate
- 1 Universal Transfer Block
- 4 Dops (4MM Flat & Cone; 8MM Flat & Cone)
- 1 Flexible Post Lamp
- 1 Maintenance/Instruction Manual
- 1 E.M.S. (Electronic Micro-Stop)
- 1 Stainless Steel Splash Pan
- Accessories (Including Allen Wrenches, Spare Fuse,
MACHINE SPECIFICATIONS
- Motor Controller Voltage: 120 VAC USA (or 240 VAC as requested)
- Electronic Micro-Stop Voltage: 120 VAC USA (or 240 VAC as requested)
- Motor Controller Fuse: 6AMP - 250 V
- Motor: 90 or 180 VDC Permanent Magnet - Ball Bearings
- Motor Speed: No Load - 3100 RPM Approximately
- Motor Size: 1/5 HP
- Lap Speed: No Load - 1725 RPM Approximately
- Lap Size: 6" or 8"
- Dop Shaft Size: 1/4"
- Machine Size: 24-1/2" long x 11-1/2" wide x 18-1/4" high
- Mast Height Adjustment: 48 MM
- Drive Belt: Polyurethane (No adjustment required)
- Shipping Weight: 79 Pounds Approximately
- Warranty: Five (5) Year Limited Warranty
| Fac-Ette |
| MANUFACTURING, INC. |
| 9545 PLOOF ROAD, LELAND, NC 28451 PHONE: 910.371.3776 TOLL: 800.336.9248 FAX: 910.371.3708 |
 |  |  |  |  |  |  |
FIGURE INDEX
1. MAST BARREL & THIMBLE
2. PROTRACTOR
3. PIVOT BODY & DOP SPINDLE
4. SADDLE BLOCK
5. MAST & MAST BASE
6. MAST BASE GIB SCREW (DO NOT ADJUST)
7. MAST BASE CLAMP
8. SET SCREW
9. GIB LOCK PIN
10. GIB
11. MACHINE BASE
12. RUBBER FEET
13. SCREW
14. SPLASH PAN GATE
15. SPLASH PAN DRAIN
16. SPLASH PAN DRAIN O-RING
17. SPLASH PAN
18. LAP SPINDLE
19. MAST BASE DOVE TAIL PLATE SCREW
20. DRAIN TUBE
21. MAST BASE SCREW (DO NOT ADJUST)
22. MAST BASE DOVE TAIL PLATE
23. SCREW (DO NOT ADJUST)
24. NUT (DO NOT ADJUST)
25. LAP SPINDLE SCREW
26. DRIVEN PULLEY
27. DRIVEN PULLEY SET SCREW
28. DRIVE BELT
29. MACHINE BASE COVER
30. MACHINE BASE COVER SCREW
31. DRIVER PULLEY SET SCREW
32. DRIVER PULLEY
33. MOTOR
34. LABEL
35. MOTOR COVER
36. DRIP CAN LOCATOR
37. DRIP CAN LOCATOR SCREW
38. DRIP CAN
39. LAMP
40. ELECTRONIC MICRO STOP
1. MAST BARREL & THIMBLE
2. PROTRACTOR
3. PIVOT BODY & DOP SPINDLE
4. SADDLE BLOCK
5. MAST & MAST BASE
6. MAST BASE GIB SCREW (DO NOT ADJUST)
7. MAST BASE CLAMP
8. SET SCREW
9. GIB LOCK PIN
10. GIB
11. MACHINE BASE
12. RUBBER FEET
13. SCREW
14. SPLASH PAN GATE
15. SPLASH PAN DRAIN
16. SPLASH PAN DRAIN O-RING
17. SPLASH PAN
18. LAP SPINDLE
19. MAST BASE DOVE TAIL PLATE SCREW
20. DRAIN TUBE
21. MAST BASE SCREW (DO NOT ADJUST)
22. MAST BASE DOVE TAIL PLATE
23. SCREW (DO NOT ADJUST)
24. NUT (DO NOT ADJUST)
25. LAP SPINDLE SCREW
26. DRIVEN PULLEY
27. DRIVEN PULLEY SET SCREW
28. DRIVE BELT
29. MACHINE BASE COVER
30. MACHINE BASE COVER SCREW
31. DRIVER PULLEY SET SCREW
32. DRIVER PULLEY
33. MOTOR
34. LABEL
35. MOTOR COVER
36. DRIP CAN LOCATOR
37. DRIP CAN LOCATOR SCREW
38. DRIP CAN
39. LAMP
40. ELECTRONIC MICRO STOP